612.467.9367
comodo

Custom Shop

Use this page to design your custom body.  It's very easy.  Simply select from each of the categories what you want and email it to us.  If you don't see exactly what you want, please email us with your specifications. Unless otherwise stated, all bodies will have a standard edge round over.  We can generally produce a quote in one business day.

PRICING:  
This is GENERAL guideline just to give a ballpark cost.  The BASE cost for a custom body is $129.00  This is your starting point, then add any additional costs from the list below.  Again, this will result in a BALLPARK figure and yo MUST get a written quote from us to proceed.

For example:  Let's say you wanted Telecaster type body (Base $129) made out of Maple (+$10) with a Flamed Maple veneer(+$15), standard Telecaster neck pocket (+$0), with a humbucker in the bridge position (+$0), with a standard Tele control cavity (+$0), with a forearm relief cut (+$0) and a Belly cut (+ $20).  Your BALLPARK total would be $174.00

CUSTOM BODY ORDER FORM:

1.  BASE COST:   $129    (For Left Hand add $20 )

2.  BODY WOOD
     Basswood  + $0
     Alder  + $15
     Ash  + $20
     Mahogany  + $30 

3.  VENEER TYPE:
     None  + $0
     Mappa Burl  + $15
     Flame Bookmatched  + $15
     Highly Quilted Bookmatched  + $20
     Ambrosia Spalted Maple  + $15
     Spalted Chen + 20

4.  BODY SHAPE:
     Telecaster Type  + $0
     Stratocaster Type  + $0
     Supra-Strat Type  + $10
     Jazzmaster Type  + $20
     SB (headless) Type + $20

5.  NECK POCKET:
     Standard Telecaster  + $0
     Standard Stratocaster  + $0

6.  BRIDGE PICKUP CAVITY:
     None
     Standard Telecaster bridge
     Standard Humbucker
     Standard P90
     Standard Single Coil
     Any Non-standard cavity - $20

7.  MIDDLE PICKUP CAVITY:  + $10
     None
     Standard Telecaster bridge
     Standard Humbucker
     Standard P90
     Standard Single Coil
     Any Non-standard cavity - $20

8.  NECK PICKUP CAVITY:
     None
     Standard Telecaster bridge
     Standard Humbucker
     Standard P90
     Standard Single Coil
     Any Non-standard cavity - $20

9.  CONTROL CAVITY:
     None
     Standard Telecaster
     Standard Stratocaster (use this for the standard
                 Top route Strat for use with a pickguard)
     Standard Supra-Tone rear routed  + $30  (includes rear cover)

10.  BRIDGE ROUTE:
     None
     Telecaster:  Standard holes for string thru  (Note: These holes are drilled from the top and do NOT go all the way thru)
     Stratocaster:  Standard tremolo + $20 (without holes)
     Stratocaster:  6 holes for tremolo  + $30
     Stratocaster:  Fender 2 hole tremolo  +$30
     Floyd Rose:  Standard inset Floyd Rose  + $30
     Floyd Rose:  Standard 2 holes for studs  +$30

11.  FRONT CONTOUR:
     None
     Forearm Relief Cut  + $20 (Standard on Strat type)
     Supra-fit lower horn contour  + $20

12.  REAR CONTOUR
     None
     Belly Cut  + $20
     Supra-fit neck plate relief  + $30

13.  ADD FOR LEFT HANDED + $40

We do not drill the control holes unless specific X and Y coordinates and diameters are provided (X and Y zero are the centerline of the part and the rear of the neck pocket).  This was you are assured that the contorl holes are EXACTLY where you want them.

You can compute the approximate cost yourself, or, simply email us the answers to all the enumerated items above and we'll compute it for you.  For example, your email to us might look like the following:

1.  BASE - $129  

2.  Body Wood - Ash

3.  Veneer Type - Flamed

4.  Body Shape - Telecaster

5.  Neck pocket - Strat

6.  Bridge pickup cavity - Humbucker

7.  Middle Pickup Cavity - Single coil

8.  Neck pickup cavity - SIngle coil

9.  Control Cavity - Standard Tele

10.  Bridge Route - NONE

11.  Front Contour - Forearm relief

12.  Rear Contour - Belly Cut